Garage Door Opening by Itself? Here is Why

    Need your garage door fixed ASAP? Looking for professional maintenance services?

    When it comes to a garage door repair in Mississauga, You need an expert you can count on. Our technicians are standing by to take your call.

    CALL NOW: ☎️ (647) 6973192

    Or, fill out the following form and we will contact you as soon as possible

    Show us the damage: Send us some photos for a FREE cost estimate.

    Our service areas include: Ajax, Pickering, Scarborough, North York, Markham, Vaughan, Etobicoke, Brampton, Mississauga and the Toronto area

    Garage Door Opening by Itself? Here is Why

    Childproofing a Garage Door

    Garage Door Opening by Itself? Here is Why and What You Can Do About It.

    Unlikely circumstances are often inevitable.

    Any unusual remarks visible in the garage door might need assistance from skilled garage door specialists.

    So, if the garage door opener is opening by itself, there is something wrong with it.

    Some parts might be damaged or triggered by a specific factor.

    An electric garage door is a complex device.

    Its parts are intertwined with each other.

    Whenever a part malfunctions, others will be affected, obstructing the operation of the entire door.

    Here are the reasons why and what homeowners can do to solve this dilemma.

    Contact for immediate assistance if the causes cannot be identified.

    Check the safety sensors.

    Electric garage doors have sensors that can detect anything struck underneath the door.

    Homeowners will be notified if there are any obstructions because there is a blinking light on the opener or at the operator button.

    There are sensors in the motor and on each side of the opening, located near the floor and mounted on the tracks.

    It can detect even the tiniest obstruction such as snow, leaves, ice, and dirt.

    Whenever the door goes up immediately on its own upon closing, there might be something that hinders it.

    It will not function if something is blocking the path.

    Clear out debris or any fragments that affect its operation.

    After clearing out, scan the safety sensors once more.

    Another reason might be the misalignment of these sensors.

    When it is not functioning correctly, it affects the door as well.

    Check these wires’ condition and the connections.

    Moreover, if the light is not blinking, the sensors are probably damaged and might need fixing.

    Check the garage door opener button.

    The garage door has an operator button like a front door has a doorbell.

    This button activates the door’s operation.

    To check it, ensure it is clean without any debris because dirt gets stuck in it easily upon pushing it.

    There is a tendency that it will get stuck which would lead to the door opening and closing simultaneously until it gets unstuck.

    So, make sure to clean the button as well as the wires and the connection in the housing.

    The cables are also sensitive components that could short circuit the door.

    Verify the garage door opener remote.

    Aside from the garage door opener, another way to open the garage door is through its remote.

    If it malfunctions, the operation of the door will be affected apparently.

    Check the remote’s functionality.

    Make sure it is clean.

    Also, verify the batteries.

    The reason might be the loose insertion of batteries, or it is not inserted correctly according to the right position.

    Change the batteries if it is concluded to be the reason.

    Radio interference is observed.

    Garage door depends on radio frequency to operate.

    It can be done whether through the passcode entry, the buttons, or the remote opener.

    All these openers and the garage door should be on a similar frequency.

    Lots of devices use the same frequencies.

    If two garage doors are programmed to the same channel, it might confuse the garage door.

    The connectivity is interrupted due to similar frequencies that are also used by neighbors or other users.

    Worry not, this problem is not difficult to solve.

    Issues regarding frequency just need reprogramming the garage door’s openers.

    Consider the control board and transformer.

    Lastly, if there are no issues seen in the reasons mentioned above, it might concern the control board in the garage door opener.

    The board might be damaged due to a power surge caused by electrical problems or a lightning strike.

    The transformer will also be affected if these problems arise.

    To solve this issue, homeowners can check the voltage of the circuit board and the transformer.

    This solution is recommended to those who are knowledgeable and handy with a multimeter.

    Furthermore, it is suggested to consider installing a surge protector.

    It puts the operator plugs into the receptacle, providing safety for the long run.

    When seeking garage door repair firms, there are technicians available in Toronto, Newmarket, Markham, and Mississauga.

    They also provide components if there are any necessary replacements.

    Garage Door Repairs tips, recommendations and frequently asked questions

    Why does my garage door opener light bulb keep dying?

    First, check for any shaking of the garage door during operation. Usually, excessive vibration can cause the filament in your opener's bulb to prematurely expire.

    One garage spring broke. I have 2, should I replace both?

    Garage door springs should ALWAYS be replaced as a set. The reason is once one spring breaks, the other one is probably not far behind, especially considering how springs weaken over time. Combining a new spring with an older one will likely cause an imbalance in your garage door's operation. If you own 2 separate garage doors and only one spring has broken, it's strongly recommended to replace the springs on each door if their springs are around the same age. Depending on your door's position, when a spring breaks it can cause serious injury as well as damage your opener.

    Does my garage door require maintenance?

    Yes. How often you will require garage door maintenance all depends on how much the door is being used. Generally, we perform the following to ensure your garage door is working properly and tuned up: We do a visual inspection of all the moving parts. We ensure the tracks; rollers and hinges are clean and lubricated properly. We make sure all nuts and bolts are tight and clean. We manually run the operator and door through a cycle to make sure it is running quietly and smoothly. Also, We check the door balance at various opening heights. If the garage door passes all these test, congratulations, you do not need a tune-up.

    Can I use the old tracks for a new garage door?

    Using old garage door tracks with a new garage door is quite dangerous. Surprisingly or not, many home and business owners try to reduce costs on a new garage door installation by reusing their old garage door track with new panels. While this might reduce the cost, the new door can get damaged faster than normal and derail.

    How hard is it really to replace a garage door?

    Installing a garage door isn't as simple as installing a regular door. More so, installing it incorrectly can be dangerous. You should call a professional garage door technician.

    How long does it take to change a garage door?

    if done properly, roughly 3 to 4 hours.

    Contact Us